N70 Transfer Case Handbrake Kit

WAITING ON PARTS FROM USA! COVID DELAYS.  3-4 WEEK WAIT.

FINALLY AN ANSWER TO ALL YOUR HANDBRAKE (or lack thereof) PROBLEMS!

Introducing the BBG transfer case handbrake kit - a no fuss, premium quality bolt-on solution!

Precision CNC machined from high strength aircraft grade 7075 T6 Aluminium with a Mil-spec Hard Anodised finish for ultimate durability and a sleek appearance.

Unlike anything else on the market, this kit:

• Is precision CNC made (not some bulky bits of mild steel MIG welded together)
• Is located in a nice concealed spot, minimising potential damage
• Minimalist componentry 
• Will never rust (except for steel disc rotor obviously)
• Does NOT require output shaft flange removal
• Can be completely bolted on in under 30 minutes
• Is completely adjustable
• Multi PCD hub to suit most Hilux output shaft PCD's
• Includes extremely in-depth installation instructions and videos
• Caliper and pads designed specifically for static holding ability

Supported models:

All models of N70 Hilux 

THIS IS A 'PRE-ORDER' THERE WILL BE A FEW WEEKS BEFORE BBG HAVE EVERYTHING MACHINED AND BOXED UP TO SEND OUT. FROM THEN ONWARDS BBG WILL BE KEEPING KITS IN STOCK - SO PLEASE KEEP THAT IN MIND. 

Benefits of a disc brake transfer case handbrake:

• It actually works (and it works exceedingly well) - unlike the factory drum brake at each wheel.
• By clamping the tail shaft at the transfer case you are effectively quadrupling the clamping force of the brake due to the differential ratio
• Being a disc setup; mud and water will not get trapped inside and limit/ruin the internal components of the assembly like a drum brake
• This kit frees you up to removing your drum brakes on the rear and using our other rear wheel disc brake conversion kit - CLICK HERE 
• Simplifies the vehicles handbrake system - which is especially handy for those who have swapped rear axles from other vehicles
• The disc hub is multi drilled which fits most common Toyota tail shaft PCDs - so you can take this with you if you change transfer cases or even get a different car.

What you get:

• 1 x BILLET BRAKE DISC HUB & BRAKE DISC ASSEMBLY
• 1 x BILLET CALIPER MOUNTING BRACKET
• 2 x BILLET BRACKET SPACER BOSSES
• 2 x BILLET CALIPER SPACER BOSSES
• 1 x BILLET CABLE JOINER
• 1 x BILLET CABLE RETAINER
• 1x BILLET CABLE BRACKET
• MECHANICAL BRAKE CALIPER WITH CUSTOM BILLET BRAKE PAD SPACER
• PRE-TERMINATED BRAKE CABLE
• HIGH TENSILE BRACKET & CALIPER MOUNTING BOLTS (BRACKET BOLTS ARE MODEL SPECIFIC)
• HIGH TENSILE TAILSHAFT MOUNTING BOLTS & CONELOCK NUTS

GOT AN N70 THAT'S RUNNING AN N60 CHAIN DRIVEN CASE?

Too, easy. Just select your option in the drop down boxes when checking out. You will need to remove one of the main case bolts and check its diameter. It will either be M8 or M10 depending on what model vehicle it came from. There are a few additional bits of hardware needed for this bracket/case combo so there is a minor additional cost.

FLAT RATE AUSTRALIA WIDE POSTAGE

$15.80 - HANDBRAKE ONLY

$17.80 - HANDBRAKE & REAR DISC COMBO

DISCLAIMER:

We are solely the supplier of goods. These are intended for 'off-road' use. We take no responsibility for any faults to do with installation of the product or any on-road legalities. Please take your car to a licensed mechanic if you do not know what you're doing or are not comfortable with undertaking this job.

We do not cover any damage done to this kit from underbody impacts from objects off-road. If you are using your vehicle for serious off-roading, it is well advised to have correct underbody armour installed or made to suit - to shield all key underbody components

THIS IS NOT A DRIFT HANDBRAKE, IT IS A STATIONARY PARK BRAKE - PLEASE DO NOT ACTUATE THE HANDBRAKE UNTIL YOU HAVE COME TO A STOP OR CLOSE TO IT. The forces exerted through this brake can quite easily snap a tail shaft or other driveline components.